BL need to be MANUALLY signed?

The forum is dedicated to all who deals with LCs. Please share your experiences, problems and opinions with us. You are requested to be confined to LC related issues only. Let us together discover the beauty of Letter of Credit. Thank and regards – admin; besttradesolution.com
Post Reply
Mokhaimad
Posts: 1
Joined: Thu Oct 31, 2019 12:55 am
First Name: Mokhaimad
Last Name: MK
Organization: Self
Filter: Two Plus Two =: 4
Location: Kuala Lumpur

BL need to be MANUALLY signed?

Post by Mokhaimad » Thu Oct 31, 2019 1:18 am

Dear forumers,

I am very sorry if this question has been raised before as i was unable to find from my search engine.

Need you help on my scenario:-

3/3 Original BL (OBL) presented as per LC requirement. However, 2/3 OBL evidencing signing capacity as below:-

Preprinted: 'As Agent For The Carrier : ABC Lines'
Stamp in blue ink:
XYZ Co Ltd
.........
(Autorized signature)

The line (..........) was blank with no manual signature.

I received a rejection from IB quoting 'BL not signed.'

As far as i understood from ISBP A35a, there were no requirement for BL to be manually signed even there was a column for signature above word 'Authorized Signature', unless LC asked for manual signature. Even though 1/3 OBL bearing an initial/handwritten signature, it just a legacy practice. Since we can clearly identify carrier and agent, the BL considered 'signed' as per UCP.

Your opinion will be highly appreciated.

User avatar
picant
Posts: 2026
Joined: Wed Aug 20, 2008 1:49 pm

Re: BL need to be MANUALLY signed?

Post by picant » Thu Nov 07, 2019 12:27 am

Hi Pal,

IMHO, the 2/3 original bill of lading must be signed.
A carrier agent in issuing's bank Country could sign the bills of lading, so those
were no more discrepant.
However if the issuing bank and applicant have no more interest, it is hard to say.....
In case of dispute the Court could judge that one original bill of lading is sufficient to take up
the goods, but this is not a UCP 600 issue.
Good luck.
Ciao

cristiand969
Posts: 754
Joined: Tue Aug 05, 2008 1:52 pm
First Name: Cristian
Last Name: D.
Organization: Bank
Filter: Two Plus Two =: 4
Location: RO

Re: BL need to be MANUALLY signed?

Post by cristiand969 » Thu Nov 07, 2019 1:28 pm

The bill of lading is not signed in line with UCP and ISBP.
Should the preprinted wording shown XYZ as agent of the carrier and then XYZ stamp has been applied, then the stamp had the value of the signature. In this particular case, the stamp just shows the agent name but the agent should have signed in any acceptable ways (manual, facsimile, etc)
Regards

afoonline
Posts: 5
Joined: Fri Jul 19, 2019 8:53 pm
First Name: AFOLAYAN
Last Name: ABIODUN
Organization: CORONATION MERCHANT
Filter: Two Plus Two =: 4
Location: NIGERIA

Re: BL need to be MANUALLY signed?

Post by afoonline » Wed Nov 13, 2019 5:10 pm

The Bill of lading not need to be manually signed, some Bill of lading have been programmed signed with machine.

Sanaur
Posts: 20
Joined: Mon Sep 16, 2019 11:01 am
First Name: Mohammad Sanaur
Last Name: Rahman
Organization: XYZ
Filter: Two Plus Two =: 4
Location: Bangladesh

Re: BL need to be MANUALLY signed?

Post by Sanaur » Fri Nov 15, 2019 9:01 am

Hi Mokhaimad, BL need to be signed and there are different ways that counts as "signed". Whatever way the BL is "signed", it need to be consistent among full set of BL.

If 1/3 BL was manually signed above the signature line, the rest were also need to be signed in similar fashion (unless credit specifically says otherwise).

Issuing bank is correct.

Regards

Post Reply